#堆叠线缆连接
CE6800-1 40ge 1/0/1 to CE6800-2 40ge 1/0/1
CE6800-1 40ge 1/0/2 to CE6800-2 40ge 1/0/2
#通过CONSOLE口配置CE6800-1的堆叠参数
<HUAWEI> system-view
#配置堆叠优先级、堆叠ID和域编号。
[~HUAWEI] stack
[~HUAWEI-stack] stack member 1 priority 200
[*HUAWEI-stack] stack member 1 domain 10
[*HUAWEI-stack] quit
[*HUAWEI] commit
#创建堆叠端口。
[~HUAWEI] interface stack-port 1/1
#将堆叠物理成员端口加入堆叠端口。堆叠端口的起止编号需与物理连线一致。
[*HUAWEI-Stack-Port1/1] port member-group interface 40ge 1/0/1 to 1/0/2
[*HUAWEI-Stack-Port1/1] quit
[*HUAWEI] commit
[~HUAWEI] quit
#保存配置脚本。
<HUAWEI> save
Warning: The current configuration will be written to the device. Continue? [Y/N]:Y
#按Enter键
Info: Please input the file name(*.cfg, *.zip, *.dat)[vrpcfg.zip]:
Now saving the current configuration to the slot 1
Info: Save the configuration successfully.
#重启交换机,耗时约5分钟。
<HUAWEI> reboot
...
Warning: The system will reboot. Continue? [Y/N]:Y
...
#关闭堆叠接口。
<HUAWEI> system-view
[~HUAWEI] interface stack-port 1/1
[*HUAWEI-Stack-Port1/1] shutdown
[*HUAWEI-Stack-Port1/1] quit
[*HUAWEI] commit
[~HUAWEI] quit
<HUAWEI> save
Warning: The current configuration will be written to the device. Continue? [Y/N]:y
...
#通过CONSOLE口配置CE6800-2的堆叠参数
#进入系统视图。
<HUAWEI> system-view
#配置堆叠ID和堆叠域编号。
[~HUAWEI] stack
[~HUAWEI-stack] stack member 1 renumber 2 inherit-config
Warning: The stack configuration of member ID 1 will be inherited to member ID 2 after the device resets. Continue? [Y/N]:Y
[*HUAWEI-stack] stack member 1 domain 10
Info: The operation takes effect only after the save command is executed. The device with a lower priority then will be reset in stack merging scenario.
[*HUAWEI-stack] quit
[*HUAWEI] commit
#创建堆叠端口。
[~HUAWEI] interface stack-port 1/1
#将堆叠物理成员端口加入堆叠端口。堆叠端口的起止编号需与物理连线一致。
[*HUAWEI-Stack-Port1/1] port member-group interface 40ge 1/0/1 to 1/0/2
[*HUAWEI-Stack-Port1/1] quit
[*HUAWEI] commit
[~HUAWEI] quit
<HUAWEI> save
Warning: The current configuration will be written to the device. Continue? [Y/N]:Y
#按Enter键
Info: Please input the file name(*.cfg, *.zip, *.dat)[vrpcfg.zip]:
Now saving the current configuration to the slot 1
Info: Save the configuration successfully.
#重启交换机
<HUAWEI> reboot
...
Warning: The system will reboot. Continue? [Y/N]:Y
...
待CE6800-2启动成功后,登录CE6800-1,执行如下命令。
<HUAWEI> system-view
[~HUAWEI] interface stack-port 1/1
[*HUAWEI-Stack-Port1/1] undo shutdown
[*HUAWEI-Stack-Port1/1] quit
[*HUAWEI] commit
[~HUAWEI] quit
<HUAWEI> save
Warning: The current configuration will be written to the device. Continue? [Y/N]:y
...
#验证配置结果
<HUAWEI> display stack
----------------------------------------------------------------
MemberID Role MAC Priority Device Type
----------------------------------------------------------------
1 Master 30d1-7e72-9650 200 CE6800
2 Standby 30d1-7e72-9600 100 CE6800
----------------------------------------------------------------
<HUAWEI> display stack topology
Stack Topology:
----------------------------------------------
Stack-Port 1 Stack-Port 2
MemberID Status Neighbor Status Neighbor
----------------------------------------------
1 up 2 -- --
2 up 1 -- --
----------------------------------------------
Stack Link:
----------------------------------------------------------------------------
Stack-Port Port Status PeerPort PeerStatus
----------------------------------------------------------------------------
Stack-Port1/1 40GE1/0/1 up 40GE2/0/1 up
Stack-Port1/1 40GE1/0/2 up 40GE2/0/2 up
Stack-Port2/1 40GE2/0/1 up 40GE1/0/1 up
Stack-Port2/1 40GE2/0/2 up 40GE1/0/2 up
----------------------------------------------------------------------------
推荐本站淘宝优惠价购买喜欢的宝贝:
本文链接:https://www.hqyman.cn/post/7266.html 非本站原创文章欢迎转载,原创文章需保留本站地址!
休息一下~~